Case IH SB541 Small Square Baler

Double tap to zoom

Overview

Key Features of the SB541
•Dependable high-throughput rotary feeding system
•Uses a packer fork with two paired rotating fingers
•Provides years of dependable service
•Large wagon hitch-bolt hole for easier hookup to hay wagons
•New Class VI heavy-duty driveline for improved durability

Features

Plenty of Sturdy Tines and an Adjustable Pickup Gauge Wheel

Crank out high-quality bales in all kinds of crops and crop conditions with the SB Series small square balers. They are all about productivity. With four models, these balers get the job done right with high-capacity features like wide pickups and heavy-duty, smooth rotary feeding systems.

Plenty of Sturdy, Closely Spaced, Curved Finger Tines

• Gently lift the crop while keeping leaves intact
• Rugged tine bars run on sealed ball bearings for long life and trouble-free operation

Standard Pickup Gauge Wheels Adjust to Five Positions

•  Guides the pickup through the contours of the field
•  Allows you to get every bit of the windrow

Raise Pickup for Transport

•  Select the manual latch or optional hydraulic pickup lift

 

Provides For A Uniform, Well-Shaped Bale

Huge 283-sq in (1,826-sq cm) feed opening allows SB balers to swallow large, uneven windrows. From here, the dependable Case IH feeding system takes over, providing a smooth flow of crop into the bale chamber for a uniform, well-shaped bale.

SB521 Feeding System

• Six feeder tines gently move the crop into the bale chamber, saving high-protein leaves
• Chain-driven system for durability and easy servicing

Easy Bale Density Control

All SB Series balers allow for easy bale density control by adjusting the tension applied to the bale chamber. For manual density control, tension springs are an economical choice.

•  Provides "set-it-and-forget-it" convenience
 
•  Ensures consistent bale weight and density

 

Case IH Small Balers Ties and Twists

Case IH small bales hold up to handling from the rack to the elevator and from the barn to the bunk.

Dependable Gear-driven Twine Knotters:

•  Hard-surface material at all wear points
•  Bill hooks are chrome plated for extra durability and reduced maintenance
•  SB541 is also available with a gear-driven wire twister

Large-Capacity Twine Storage Increases Field Time Between Refills:

•  SB521 — load four balls of twine
•  SB531 — load six balls of twine
•  SB541, SB541c and SB551 — load eight balls of twine
•  SB541 wire-tie version features four-coil wire storage

Simple Design and Easy Operation

Fill your wagon with bales as you make them with the optional Case IH BTX11 bale thrower, available with the SB521, SB531 and SB541.

•  Smooth, reliable hydraulic drive throws the bales
•  Handles bales up to 38 in (965 mm) long and up to 70 lbs (32 kg)
• Easy operation from your tractor seat
• Move the Case IH bale thrower to the left or right to fill the corners of the wagon
• Adjust the belt speed to load the front or the back of the wagon
• The simple design of the BTX11 allows for easy installation, adjustment and service

Specifications

Make Case IH
Model SB541
Bale size  
Bale cross section, h x w, in (mm) 14 x 18 (356 x 457)
Bale length range, in (mm) 12 to 52 (305 to 1321)
Density control, standard Adj spring loaded tension rails
Density control, optional Adj hydraulic density
Bale thrower compatible BTX11 available (80 lb bale)
Pickup  
Pickup position Offset to right side
Sweep width on flare, in (mm) 80 (2030)
Sweep width inside, in (mm) 75 (1900)
Width between outside tines, in (mm) 67.5 (1714)
Tine spacing, in (mm) 2.63 (67)
Number of tines 156
Number of tine bars 6
Windguard description 13 rods
Standard pickup lift Manual
Optional pickup lift Hydraulic
Pickup protection V-belt slippage & lost motion reel drive
Feeder  
Feeder Description Rotary feeder w/ packer
Feeder opening, sq in (sq cm) 283 (1826), right side entry
Plunger  
Plunger speed, strokes/min 93
Plunger stroke, in (mm) 30 (762)
Tying mechanism  
Tying mechanism type Knotter or wire twister
Tying capacity (twine), balls 8
Tying capacity (wire), coils 4
Main Drive  
Flywheel diameter, in (mm) 22 (559)
Flywheel weight, lbs (kg) 248 (112)
PTO Driveline Std three-joint, Category 6
PTO Speed, rpm 540
Main drive protection Shearbolt, overrunning & slip clutches
Tires  
Standard tire, left 31 x 13.50 - 15, 6PR
Standard tire, right 27 x 9.50 - 15, 6PR
Dimensions  
Max. height, in (mm) 71 (1803)
Width, in (mm) 120 (3048)
Length w/o bale chute, in (mm) 205 (5207)
Length w/bale chute, in (mm) 247 (6274)
Weight  
Weight w/twine tie, lbs (kg) 3,715 (1685)
Weight w/wire tie, lbs (kg) 3,851 (1747)
Tractor Requirement  
Tractor PTO Power, hp (kW) 75 (56)
Sales Literature  
Literature number CIH7180801
Literature date 7/1/2008
Manual  
Manual number 86624842
Manual date 10/1/2001
Entry Date  
Manufacturing status Current
First Entry Date 8/1/2008
Revision Date 2/1/2012

DON'T MISS OUT ON THE LATEST DEALS

Add us to your inbox to stay up to date and learn more